Thermostatic steam trap - VYC INDUSTRIAL
+34 93 587 22 22 | WhatsApp : +34 628 512 590 grm@grmindustrial.es
Index » Productos » Industrial accesories » Steam accesories » Steam traps » Thermostatic steam trap

THERMOSTATIC VENTER

TO REMOVE SATURATED OR SUPERHEATED STEAM CONDENSATE AT MEDIUM AND LOW PRESSURE

VYC 443 / 543 / 444

Temperature/pressure range: See technical sheet

Material: Stainless steel

BSP/NPT thread

Thermostatic steam trap

THERMOSTATIC VENTER

TO REMOVE CONDENSATE FROM SATURATED OR SUPERHEATED STEAM AT MEDIUM AND LOW PRESSURE

VYC 443 / 543 / 444

Temperature/pressure range: See technical sheet

Material: Stainless Steel

BSP/NPT thread

Description

TRAP FOR SATURATED OR SUPERHEATED STEAM MEDIUM/LOW PRESSURE – VYC

To extract saturated or superheated steam condensates at medium and low pressure.

Applicable in; steam pipes, ironing machines, laundries and dry cleaners, tanks and containers with condensate discharge, cooking pots, sterilizers, exchangers, multiple platen presses, vulcanization autoclaves, calenders, pressure reducing equipment, etc.

Mod.444 provided with a centering ring for placement between flanges according to EN, DIN, UNE, ANSI, BS, etc. standards. DN-15 to 25.

Principle of operation

The thermostatic action of the thermostatic trap of the pressure balanced element allows the condensate and the cold air to evacuate freely at the start running.

When the temperature of the condensate approaches saturation, the element closes and cuts off the passage of steam.

When the condensate cools, the element opens and evacuates it. Again and in the imminent presence of steam the cycle is repeated and the element closes. And so on

Thermostatic steam trap

Open

Thermostatic steam trap

Start to close

Purgador termoestático

Fully closed

Technical characteristics

TRAP FOR SATURATED OR SUPERHEATED STEAM MEDIUM/LOW PRESSURE – VYC

Threaded connection

Threaded angle connection

Connection between flanges

  • It works by the action of a thermostatic valve that opens the passage to air and cold water and condensate but closes in the presence of condensate at the point of vaporization.
  • Constructed entirely of stainless steel for its resistance to wear, temperature and corrosion. They are fully recyclable.
  • Long life cycle with high operational efficiency.
  • The three-piece design is very simple and allows for easier and faster maintenance than other steam traps of this type.
  • Easy installation with the possibility of mounting in any position.
  • Compact, robust. Much smaller weight and size than conventional steam traps.
  • Interior design of the body conceived to provide the capacities required in each case and avoid oversizing.
  • Service conditions and flow direction marked on the body.
  • Continuous download.
  • Also ideal as air vents.
  • Precise in opening and closing, avoiding steam losses.
  • Absolutely silent.
  • They remain unperturbed by vibrations, water hammer, superheated steam, corrosive condensate, frost, etc.
  • Protective filter of the closing surfaces designed so that the entire surface works equally. This guarantees a much higher filtering capacity than its competitors. Access to the filter is very easy and fast.
  • Treated, ground, lapped and burnished sealing surfaces, thus achieving a degree of tightness, even higher than that required by EN 12266-1.
  • All steam traps are rigorously tested and verified.
  • Each one of the components is numbered, registered and controlled. If previously requested, the trap will be accompanied by certifications of materials, castings, tests and performance.
  • Mod.444 with reduced assembly length according to EN-558, basic series 49. This trap is provided with a single ring
  • centering for placement between flanges according to EN, DIN and UNE (PN-6, 10, 16, 25, and 40), ASA (ANSI) (PSI-150 [except DN-15], 300) and other standards standards (NF, BS, etc.)

Downloads

TRAP FOR SATURATED OR SUPERHEATED STEAM MEDIUM/LOW PRESSURE – VYC

Ask request

8 + 10 =

1